How to install drive belt windstar 1998

Use a pair of medium sized slip joint pliers, upside-down and tilted slightly to the left, to pull back on the tensioner. You will get plenty of slack and keep all of your fingers. I have a Windstar, and in it there is a belt tensioner pully which swings on an eccentric radius that tightens the belts around the other pulleys on the front of the engine not front of van due to transverse mount.

This is accessed by elevating the vehicle passenger side near the front axle like you would if removing the front right tire and above the front axle near the top of the fender wall is this pulley. If looking at the engine under the hood, it would be near the fire wall down by the fender. Once located then use a 13mm wrench box end preferably to swing the tensioner pulley toward the front of the van.

This will loosen the belt where it can be pulled off the pulley. Make sure you use place the wrench where adequate swing can be achieved. If the belt has come off, simply find a diagram, or go by the pulley grooves or flat to understand which side the belt goes.

Mine was broken, so I had to do that. It was easier for me to start from the top under the hood but leave the alternator pulley as the last one to wrap over I did this with help, as I had the pulley swung, someone else wrapped the belt over the alternator pully.

There's a square hole behind the tensioner You need to get under the car and get the socket wrench and fit the head into the square hole. You will also need some hollow steel tubing to place over the wrench handle for use as a breaker.

You will need this for leverage to get enough clearance to fit the new belt on. Find the tensioner by pointing a flashlight into the engine compartment just to the rear of the alternator pulley. Then slide unde the car next to the passenger side wheel. The bolt on the tensioner is 12mm. You'll need to use a box or open end wrench. Turn the wrench counterclockwise to take the tension off. To replace a worn belt, locate the idler or generator pulley.

Loosen the hold-down fastener for the idler or generator pulley. Pry the idler or generator pulley inward to release the belt tension and remove the belt. Match the old belt up for size with the new replacement belt. Observe the belt routing diagram in the engine compartment. Pry the idler or generator pulley to adjust the belt to specifications. Tighten the idler or generator pulley fastener. Start the engine and check the belt for proper operation.

If I remember correctly you torque frontward and the belt will release. Hope it can help! By the way, my van does not have the serpentine belt diagram sticker, so be sure to take a look if you have one, and if not, take a paper and mark the location of the belt through the different pullies before removing the old one.

How do you replace the serpentine belt in sunfire. Replace serpentine belt on Chevy avalanche? Since the Monterey is the direct spin off of the Windstar, check out the "Related Questions" below Where to find an online serpentine belt diagram for Windstar - and how to replace? Replace it. Google it. How do you replace peugeot serprntine belt. How do you put on a serpentine belt on a Isuzu axiom.

The Camry did not have a serpentine belt. Do you have a Corolla? Saab dealer quoted 1 hour to replace the serpentine belt. How long will it take to replace a belt tensioner unit and serpentine belt in a lexus sc? I need daigram of ford focus se serpentine belt. Everything you could want to know about Windstar serpentine belts is in the "Related Questions" The cost to replace a Mazda Protege serpentine belt will vary depending on the cost of parts and cost of labor.

You don't repair a serpentine belt. You replace the worn or broken belt with a new one. Loosen the tensioner pulley. The serpentine belt will become loose and can be removed. Put the new serpentine belt on and tighten the tensioner pulley. How to remove and install the serpentine belt on Chevy Blazer with AC? You can try this video guide on repairing the serpentine belt. Slide the tensioner pulley to the left.

The serpentine belt will become loose. Reverse the process to install the new serpentine belt. See "Related Questions" below for a discussion regarding the serpentine belt tensioner and pulley. Pretty comprehensive coverage. Log in. Serpentine Belts. Ford Windstar. Toyota Matrix. How To. Study now. See answer 1. Best Answer. Easier than you think. NOTES: The belt is recommended to be replaced around 60, miles There is a wear indicator minimum vs maximum on the face of the tensioner arm to let you definitively now when it's time to change the belt.

Answer This is a very simple task. Good luck. Tips: remember the two pulleys that don't have the grooves in them will be against the smooth side of the belt Answer The serpentine belt tensioner is spring loaded. Answer if you're under the hood, look at all the pulleys.

Answer You need to obtain a flat serpentine changing wrench. Answer I couldn't find a flat serpentine wrench breaker bar - the local stores used to carry them. Answer A small rope on the end of the 15MM wrench will hold the tensioner or a helper can pull on the rope.

Answer I labored with this one for quite a while, searched the internet, and then someone at work told me the secret. Answer It took me four hours to replace the belt on my Windstar Good Luck! Answer Purchase a serpentine belt wrench. Answer And for a Windstar 3.

Answer Actually, the info from the linked question was not correct for a Windstar 3. Reverse procedure to reinstall. Make sure that all of the V-grooves make proper contact with the pulleys. Answer Well it's probably the same as the Windstar, so if it is: you need a 13mm key.

See "Related Questions" below for links to online sources of belt routing diagrams. Answer I have successfully changed my serpentine belt on my '96 Windstar. Answer First, buy the correct belt, then look on the fan shroud which should give the route that the new belt should take. Answer First of all, you will need to locate the drive belt tensioner and the drive belt tensioner pulley.

Answer Just replaced alternator on my Windstar. Answer My brother has a ford Windstar 6 cyl 3. Here's a procedure I've used: 1 Disconnect the negative battery cable. If something amiss, you may have to repeat the proce Answer NOTE: The "official" way to release the belt tension is to rotate the tensioner about degrees counter clockwise, and press a flexible metal leaf on its side into a holding slot. Answer To replace a worn belt, locate the idler or generator pulley. Answer An answer is found in the linked question I have a Windstar, and in it there is a belt tensioner pully which swings on an eccentric radius that tightens the belts around the other pulleys on the front of the engine not front of van due to transverse mount.

I hope this help Answer pully is at the back of the engine,to left of the coil pack,a 15mm wrench fits the bolt,pull it toward you Ford Windstar - You'll need to put the car on jack stands or secure ramps.

Study guides. Q: How to replace the serpentine belt on a Windstar? Write your answer Related questions. Does a ford windstar have an alternator belt or a serpentine belt.? How do you replace the serpentine belt in grand am? Replace serpentine belt on Chevy Avalanche? How do you change a fan belt on a Mercury Monterey?

How to replace Serpentine belt on grand AM 2. How do you repair the serpentine belt? Where can you find a diagram to reroute a serpentine belt on a ford windstar? How do you replace Peugeot serpentine belt? How do you replace the serpentine belt on a Isuzu axiom? How do you replace serpentine belt for Toyota Camry?

How much to replace serpentine belt on Saab 93? How long will it take to replace a belt tensioner unit and serpentine belt in a Lexus sc? How do I replace Ford Focus serpentine belt? What does the diagram look like for the serpentine belt for a Ford Windstar? How much is it to replace a 99 Mazda protege serpentine belt? How do you repair the serpentine belt on a Mitsubishi Galant? How do you change serpentine belt sante fe? How do you replace a serpentine belt on a 92 S10?

How do you replace a serpentine belt in a Chevy truck? How do i replace the serpentine belt pn a econoline van? How to replace a serpentine belt on buick lesabre? How do you replace serpentine belt on a Volvo s60? How to replace an iDLERer pulley on a ford windstar van? How do you replace a serpentine belt on a Ford Escort?

How do you replace a serpentine belt on a Bravada? Study Guides. Trending Questions. Which reactant was the limiting reactant in the vinegar lab? Why is it important to balance a chemical equation before proceeding to answer questions about it? What is the difference between theoretical and actual yield? List two observations from the vinegar lab that imdicates a chemical reaction took place? Still have questions? Find more answers. Previously Viewed. Pivot the tensioner pulley clockwise or away from the belt to release the belt tension, keeping your fingers away from between the belt and the pulleys at all times.

Compare the new belt to the old one. The new belt might be slightly shorter but the configuration should be the same.

Run the new belt through all the pulleys except the belt tensioner pulley. Use the serpentine belt diagram or your own notes as a reference, if necessary. Slide the new serpentine belt over the tensioner pulley and carefully release the tensioner pulley. Remove the tool from the engine compartment and run your fingers over the pulleys to make sure the belt is properly seated on the pulley ridges. Since Dan Ferrell has contributed general and consumer-oriented news to television and the Web.

His work has appeared in Texas, New Mexico and Miami and on various websites. Items you will need Wrench Serpentine belt tool Ratchet and socket, if necessary Screwdriver, if necessary. Duffy;